| Product | Cost | Date Installed | Rating | Comments |
|---|
| Walbro - 255 L/PHR fuel pump | $0.00 | | | About right for the stroker motor. |
| BBk - air intake | $0.00 | | | Used lower elbow and maf mount to slide air intake into fender |
| BBK - Mustang 75mm throttle body | $0.00 | | | Same as the trucks just flipped around to work with the new manifold. |
| BBK - Shorty headers | $0.00 | | | Good fit....... no leaks. |
| Beltech - drop coil springs | $0.00 | | | Nice product. |
| Beltech - Hangers & Shackles | $0.00 | | | Good product. 5 inch drop in rear. |
| BMP - Waterpump | $0.00 | | | A hi-perf water pump that takes up a little less hp. |
| Boss - 304 wheels | $0.00 | | | 18x9 inch wheels. Have held up well. |
| Comp cams - Beehive springs | $0.00 | | | a little insurance with the higher lift cams. |
| Comp Cams - camshafts | $0.00 | | | Custom grind based on the 602 series to match my motor and the nitrous. |
| Compucar - Bottle heater | $0.00 | | | It works. If you live in a colder clime a must. |
| Custom - c-notched bed | $0.00 | | | Had to make room for the driveshaft. |
| Custom - Leaf springs | $0.00 | | | Re-arched rear leafs to bring rear down 1 inch. |
| Custom - Transmission | $0.00 | | | Complete 4r70w rebuild to Transgo specs. hardened gears, 5 and 6 pack clutches on 1 and 2, etc..... |
| Diablo - Flip chip | $0.00 | | | Flip chip with n/a tune for street and full blown race/nitrous tune for the strip. |
| DJM - c-notches | $0.00 | | | Worked great needed the clearance with almost a 6 inch drop in the back. |
| Doesch Tech - Shocks | $0.00 | | | Very nice ride. Great drop shocks. |
| Flexalite - Dual electric fans | $0.00 | | | Nice kit. Good fit, retains shroud cover and works great!! |
| Ford - rear sway bar | $0.00 | | | Rear Lightning sway bar. Nice differnce to cornering. |
| Kuhmo - Ectsta STX | $0.00 | | 8 | 255/55's on front 275/55's on back...... very nice tire for money. Hook up good too. |
| Lakewood - Traction Bars | $0.00 | | 8 | Stop that wheel hop........... Works great!!! Powder coating is a little to be desired. |
| Motorsport - 30 lb injectors | $0.00 | | | With the Motorsport 90mm MAF can be jacked up to 32 lbs. perfect for my engine. |
| Motorsport - 90 mm MAF | $0.00 | | | Easy to tune , snap to install. |
| MSD - Coil packs | $0.00 | | | Direct replacement and a little added spark for the the motor and Nitrous. |
| MSD - Digital window | $0.00 | | 9 | Allows me to set the rpms the nitrous comes on and off. Nice tuning feature for the track. |
| MSD - Super conductor wires | $0.00 | | | Great fit!! |
| Nitto - Nitto 555 drag radials | $0.00 | | | Definately better than stock tires for hook. probably upgrade to full slicks. |
| PI heads - Sean Hyland | $0.00 | | | A modified set of stage 2's. For Nitrous |
| Richmond - 4.10 gears | $0.00 | | | Just a gear set. |
| Short block - Stroked 4.6 | $0.00 | | | manley rods and pistons 20 over. Forged crank, billet oil pump gears,etc |
| Steeda - Pullies | $0.00 | | | Easy install...... nice product. |
| SVT - Cobra posi unit | $0.00 | | | Works great.......big difference from the open rear-end. |
| T and A perfromance - Rear cover and girdle | $0.00 | | 9 | Keep the rear in place for those hard launches. Nicely machined product and easy install. |
| TCS - 10 inch converter | $0.00 | | | Billet converter. Anti-ballon plates...etc 3000 stall speed on my truck!! |
| Transgo - Shift kit | $0.00 | | | Great kit. |
| Trick flow - 4.6l intake manifold | $0.00 | | | Alot of work......... looks like it will work great. Will know when I see the #'s. |
| Western chassis - control arms | $0.00 | | 10 | Lowering 2 inch. Well built and easy swap. Great quality.....Great ride!!! |
| WMS - Intake | $0.00 | | | Nice intake........easy install. Top half of my custom system. |
| Zex - Zex Ford efi Kit | $0.00 | | 9 | Changed over to a zex system......... good result, better motr safety |
None.
